02-06-2014, 11:25 AM,
(This post was last modified: 02-06-2014, 11:27 AM by christianos.)
|
|
christianos
Junior Member
|
Posts: 4
Threads: 1
Joined: Feb 2014
Reputation:
0
| |
abrasive resistant coating for titanium
Dear All,
I have a component made of titanium (Ti64) which has to be coated.
The coating should be an abrasive resistant coating and should not be thick to preserve geometry of the component.
I was thinking about some PVD coatings (TiAlN) or even DLC (diamond like coating), however, I'm not sure how that would work with low modulus titanium.
In addition, PVD process involves high temperature (high vacuum at 150 -500 Deg C). Would I need some stress relaxation after the process? How that would affect the coating itself?
Many thanks,
Chris
|
|
02-07-2014, 10:22 AM,
|
|
christianos
Junior Member
|
Posts: 4
Threads: 1
Joined: Feb 2014
Reputation:
0
| |
RE: abrasive resistant coating for titanium
(02-06-2014, 07:47 PM)djewell Wrote: Our company has successfully coated titanium with various materials using HVAF. It is important not to overheat titanium during coating, or it will degrade. Therefore, proper spraying and cooling techniques are necessary. Using HVAF will allow you to apply carbides or metal hardface coatings. Contact me off-line if you want to discuss further.
I've read a bit more about HVAF and HVOF and it seems they might be quite thick in general. This is a problem for some sharp edges where the stresses are the highest. In addition I am worried that these HVAF coatings would not preserve a geometry of the component.
Any experience on PVD coatings, such as TiN or TiAlN? These are used for cutting tools. The only worry is that titanium has low modulus of elasticity, thus the TiAlN coating may flake off?
Any ideas?
|
|
02-10-2014, 09:59 AM,
|
|
christianos
Junior Member
|
Posts: 4
Threads: 1
Joined: Feb 2014
Reputation:
0
| |
RE: abrasive resistant coating for titanium
(02-07-2014, 03:22 PM)djewell Wrote: HVAF/HVOF coatings do not have to be thick. They can be applied in thin layers and in such a way that they do not change the geometry of the part. Sharp edges are a problem for any coating, no matter how it is applied.
What minimum thickness of HVAF/HVOF coating are we talking about? Is is something around 5 microns or significantly more?
|
|
02-18-2014, 01:56 PM,
(This post was last modified: 02-18-2014, 01:57 PM by dejones.)
|
|
dejones
Newbie
|
Posts: 1
Threads: 0
Joined: Feb 2014
Reputation:
0
| |
RE: abrasive resistant coating for titanium
(02-06-2014, 11:25 AM)christianos Wrote: Dear All,
I have a component made of titanium (Ti64) which has to be coated.
The coating should be an abrasive resistant coating and should not be thick to preserve geometry of the component.
I was thinking about some PVD coatings (TiAlN) or even DLC (diamond like coating), however, I'm not sure how that would work with low modulus titanium.
In addition, PVD process involves high temperature (high vacuum at 150 -500 Deg C). Would I need some stress relaxation after the process? How that would affect the coating itself?
Many thanks,
Chris
you may want to check the hardide process.
|
|
03-05-2014, 09:24 AM,
|
|
christianos
Junior Member
|
Posts: 4
Threads: 1
Joined: Feb 2014
Reputation:
0
| |
RE: abrasive resistant coating for titanium
Hardide process seems to be a quite promissing one. I will have a closer look at this. Hardide looks good 'on the paper', some tests would need to be conducted to clarify this.
At the moment I am considering TiN coating, however, I am not very happy about its wear restistance properties.
Thank you All for all the replies, I appreciate it.
|
|
05-28-2014, 04:00 PM,
|
|
RE: abrasive resistant coating for titanium
Hi Chris,
I haven't been on the forum in a while, and I only just now saw your post. I work with Hardide in the US and would be happy to speak with you, but you may have already spoken with our team in the UK office.
We do have the ability to coat Ti in our CVD process, but part size and other factors can sometimes make this a challenge.
+1 713 677 3504
Regards,
Dan Wilson
|
|
|